Hunter 25602 52 Outdoor Original Bedienungsanleitung PDF herunterladen

SINCE 1 8 8

INSTALLATION INSTRUCTIONS FOR

HUNTER ORIGINAL

CEILING FANS

WARNINGS

• To avoid possible electrical shock, before wir-

ing fan, disconnect power by turning off the cir-

cuit breakers both to the outlet box and to its

associated wall switch location. If you cannot

lock the circuit breakers in the “OFF” position,

securely fasten a prominent warning device,

such as a tag, to the service panel.

• All wiring must be in accordance with national

and local electrical codes. If you are unfamiliar

with wiring, you should use a qualified electri-

cian.

• To reduce the risk of personal injury, install the

fan to the building structure according to these

instructions and use only the hardware sup-

plied.

IMPORTANT!

READ AND SAVE THESE

INSTRUCTIONS!

CAUTIONS

• NEVER REST THE FAN ON THE SWITCH HOUS-

ING. As you prepare the fan for installation, rest

the motor in the liner in which it was packed.

• Be sure to put full contents of the oil tube into

the fan according to the instructions.

• If this fan is used as a replacement for an Origi-

nal

Old-Tyme non-reversible fan, it must be in-

stalled per the instructions included with this

fan. Failure to do so could result in the fan fall-

ing. DO NOT HANG THIS FAN ON A SINGLE

“J” HOOK.

• To reduce the risk of noise and to ensure proper

fan operation, do not use a solid-state speed

control with this fan. Use Hunter speed con-

trols for Hunter Original

ceiling fans only.

• Do not use an abrasive cleaner on the fan. A

mild detergent will clean and restore most units

to their original beauty.

Installing Your Hunter

Ceiling

Fan

Note To Installers: Please leave this manual with

the home owner.

Tools needed:

• Pliers • 3/8” Socket Wrench

• Flat blade screwdriver • Phillips screwdriver

• Electric drill • 11/64” drill bit

• 4” x 1-1/2” standard octagon electrical box

Step 1: Pre-Installation

1. Select the installation site: Normally this is

near the center of the room, often replacing a light

fixture. Make certain that ample clearance is left

for the rotating fan blades. For maximum effi-

ciency, no obstructions (walls, posts, etc.) should be

within 24” of the tips of the blades. See Figure 1.

NOTE: Mounting should also meet the precautions listed

in Step 3.

Read this entire manual thoroughly before begin-

ning installation.

24”

Minimum

Clearance

7’ Minimum

Clearance To

Floor

8’Minimum

to Ceiling

Figure 1

2. Fan mounting height: Your Hunter fan

comes with the proper hardware to hang the fan

from a standard 8 foot ceiling so that the fan blades

will be 12” from the ceiling and approximately 7

feet from the floor. See Figure 1.

NOTE: On vaulted ceilings, up to 45° pitch, you must

use the Hunter Vaulted Ceiling Mounting Kit.

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - CEILING FANS

Seite 2 - Fan Part

Seite 3 - Step 4: Hanging the Fan

Seite 4 - Step 5: Wiring Instructions

Seite 5 - Canopy Installation

Seite 6

Seite 7

Seite 8 - TROUBLESHOOTING

Weitere Dokumente für Fans Hunter 25602 52 Outdoor Original

Um das Dokument anzuzeigen Hunter 25602 52 Outdoor Original Bedienungsanleitung

Hunter 25602 52 Outdoor Original Bedienungsanleitung (8 Seiten)

Kommentare zu diesen Handbüchern

Keine Kommentare

Hunter 25602 52 Outdoor Original Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Fans Hunter 25602 52 Outdoor Original herunter. Hunter 25602 52 Outdoor Original User Manual Benutzerhandbuch

Inhaltsverzeichnis

Weitere Dokumente für Fans Hunter 25602 52 Outdoor Original

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Fans Hunter 25602 52 Outdoor Original