Hunter TYPE 2 Bedienungsanleitung PDF herunterladen

REV: 5/94

PAGE 1

FORM NO. 40987-01

CAUTION:

WARNING:

CAUTION:

FIGURE 3.

SHOULD EXTEND AT LEAST 6" BEYOND OUTLET BOX FOR EASE IN MAKING CONNECTIONS. SEE

MAKE CERTAIN THAT WIRING MEETS ALL NATIONAL AND LOCAL ELECTRICAL CODES. WIRE LEADS

B. BRING ELECTRICAL CABLE INTO THE OUTLET BOX AND ATTACH WITH AN APPROVED CONNECTOR.

DO NOT USE A LUBRICANT ON SCREWS.

OUTERMOST HOLES WILL BE USED IN STEP 4B.

BOX. ORIENT THE BOX SO THE OUTERMOST HOLES ARE ALIGNED WITH THE 2 X 4 BRACE. THE

TWO #8 X 1-1/2" WOODSCREWS AND WASHERS. USE THE INNERMOST HOLES FOR SECURING THE

(2) PILOT HOLES NO LARGER THAN THE MINOR DIAMETER OF THE WOODSCREWS (5/64") AND USE

THE CEILING BY 1/16" MINIMUM. SECURE THE OUTLET BOX TO THE CROSS BRACE BY DRILLING

BETWEEN TWO CEILING JOISTS AS SHOWN IN FIGURE 2. THE OUTLET BOX MUST BE RECESSED IN

A. SECURE A METALLIC OUTLET BOX 4" X 1-1/2" OR 4" X 1/2" DEEP TO A 2 X 4 CROSS BRACE

STEP 3:

STEP 2:

STEP 1:

MUST SUPPORT A 35 LB. FAN WITH ACCESSORIES.

DO NOT MOUNT DIRECTLY TO AN UNSUPPORTED CEILING OR TO AN ELECTRICAL OUTLET. MOUNTING

ALL WIRING MUST MEET LOCAL AND NATIONAL ELECTRICAL CODES.

INSTALLATION SITE.

BE CERTAIN ELECTRICITY IS "OFF" AT THE FUSE PANEL WHEN INSPECTING OR REPAIRING

TO THE CEILING.

PRECAUTIONS MUST BE TAKEN FOR SAFETY AND TO ENSURE THAT YOUR FAN IS SECURELY MOUNTED

YOUR HUNTER CEILING FAN WITH ACCESSORIES CAN WEIGH UP TO 35 LBS. THE FOLLOWING

INSTALLATION OF OUTLET BOX AND ROUGH-IN WIRING

C. CHECK CONTENTS TO BE CERTAIN IT CONTAINS A BAG OF PARTS.

RETURN ALL BLADES IN THE SET FOR REPLACEMENT.

AS THEY WERE SHIPPED. SHOULD ONE OF THE FAN BLADES BECOME DAMAGED DURING SHIPMENT,

MORE THAN ONE FAN IS BEING INSTALLED, KEEP THE MATCHED AND BALANCED FAN BLADES IN SETS

B. CHECK FOR ANY SHIPPING DAMAGE TO THE MOTOR, FAN BLADES, SWITCH HOUSING, AND GLOBE. IF

A. UNPACK UNIT CAREFULLY TO AVOID ANY DAMAGE TO THE COMPONENTS.

INSPECTION OF FAN AND LIGHT

SEE FIGURE 1. FOR MOUNTING DISTANCES.

THEY SHOULD NOT HAVE ANY OBSTRUCTION (WALLS, POSTS, ETC.) WITHIN 24" OF THE BLADE TIPS.

C. THE FAN BLADES MUST BE MOUNTED AT LEAST 7' ABOVE THE FLOOR. FOR MAXIMUM EFFICIENCY,

FROM ANY HARDWARE STORE OR ELECTRICAL SUPPLY HOUSE.

NEED A 4" X 1-1/2" OR 4" X 1/2" OUTLET BOX AND WIRE NUTS (2) WHICH CAN BE PURCHASED

B. INSTALLATION HARDWARE IS INCLUDED FOR A STANDARD DRYWALL OR PLASTER CEILING. YOU WILL

PRECAUTIONS LISTED IN STEP 3 BELOW.

IN CONTACT WITH THE ROTATING FAN BLADES. THE MOUNTING SITE SHOULD ALSO MEET THE

A. SELECT INSTALLATION SITE. CHECK TO MAKE SURE THAT IN NORMAL USE NO OBJECT CAN COME

PRE-INSTALLATION INSTRUCTIONS

IN BETWEEN ROTATING FAN BLADES.

THE BRACKETS, BALANCING THE BLADES, OR CLEANING THE FAN. DO NOT INSERT FOREIGN OBJECTS

2. TO REDUCE THE RISK OF PERSONAL INJURY, DO NOT BEND THE BLADE BRACKETS WHEN INSTALLING

WITH THIS FAN. USE HUNTER CONTROL MODEL 22691.

1. TO REDUCE THE RISK OF FIRE OR ELECTRICAL SHOCK, DO NOT USE A SOLID STATE SPEED CONTROL

UNFAMILIAR WITH WIRING, YOU SHOULD USE A QUALIFIED ELECTRICIAN.

3. ALL WIRING MUST BE IN ACCORDANCE WITH NATIONAL AND LOCAL ELECTRICAL CODES. IF YOU ARE

BEFORE WIRING.

2. TO AVOID POSSIBLE ELECTRICAL SHOCK, BE CERTAIN ELECTRICITY IS SHUT OFF AT MAIN PANEL

1. READ ENTIRE INSTRUCTIONS CAREFULLY BEFORE BEGINNING INSTALLATION.

READ AND SAVE THESE INSTRUCTIONS

FOR TYPE 2 HUNTER CEILING FAN WITH LIGHT

INSTALLATION INSTRUCTIONS

10"

84" MIN

8 FT. MIN

CEILING TO FLOOR

24"

CLEARANCE

TO OBSTRUCTIONS

FIGURE 1.

TO FLOOR

1 2 3 4 5

Inhaltsverzeichnis

Seite 1

REV: 5/94PAGE 1FORM NO. 40987-01CAUTION:CAUTION:WARNING:CAUTION:FIGURE 3.SHOULD EXTEND AT LEAST 6" BEYOND OUTLET BOX FOR EASE IN MAKING CONNECTI

Seite 2 - FAN ASSEMBLY

REV: 5/94FALLING.SCREW COULD RESULT IN FANUNSCREWING.IS IN THE UP POSITION.NOTE:ASSURES LOCKING TAB IN CANOPYHOLES IN CEILING PLATE THATMUST BE IN UP

Seite 3 - FINISH FAN ASSEMBLY

REV: 5/94FIGURE 7.CANOPYCEILING PLATEMOUNTING SCREW (3)MOUNTING SLOTS (3)SEE FIGURE 7A.MAKE CERTAIN GROOVE AND TAB ARE ENGAGED BEFORE RUNNING FAN.FAI

Seite 4 - BULB AND GLOBE INSTALLATION

REV: 5/94MOUNT BLADES TO FAN WITH WOOD PADDLES LOCATED UNDERNEATH BLADE BRACKETS.UNTIL SOUND HAS DISAPPEARED.NOTE: SHOULD GLOBE EMIT ANY SOUND WHEN F

Seite 5 - STEP 10:

C 1989 HUNTER FAN COMPANYREV: 5/945. RE-ADJUST 3 GLOBE MOUNTING SCREWS.5, GLOBE IS VIBRATING AND EMITTING NOISE.*1. USE BALANCING KIT (SEE STEP 8C).

Kommentare zu diesen Handbüchern

Keine Kommentare

Hunter TYPE 2 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Haushaltsfans Hunter TYPE 2 herunter. Hunter TYPE 2 User's Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Haushaltsfans Hunter TYPE 2